[pgpool-general: 7374] Re: Watchdog New Primary & Standby shutdown when Node 0 Fails
Joe Madden
Joe.Madden at mottmac.com
Fri Dec 18 22:48:20 JST 2020
Hi Tatsuo,
I am using the RPM version which I think according to github still has node 0 for example:
https://github.com/pgpool/pgpool2/blob/V4_2_0_RPM/src/watchdog/watchdog.c#L2244
Do you think this could cause the issue?
If I configure with node 0 always being dead:
hostname0= '192.168.40.71'
wd_port0 = 9000
pgpool_port0 = 9999
hostname1 = '192.168.40.66'
# Host name or IP address of pgpool node
# for watchdog connection
# (change requires restart)
wd_port1 = 9000
# Port number for watchdog service
# (change requires restart)
pgpool_port1 = 9999
# Port number for pgpool
# (change requires restart)
hostname2 = '192.168.40.67'
wd_port2 = 9000
pgpool_port2 = 9999
hostname3 = '192.168.40.64'
wd_port3 = 9000
pgpool_port3 = 9999
hostname0= '192.168.40.71'
wd_port0 = 9000
pgpool_port0 = 9999
hostname1 = '192.168.40.66'
# Host name or IP address of pgpool node
# for watchdog connection
# (change requires restart)
wd_port1 = 9000
# Port number for watchdog service
# (change requires restart)
pgpool_port1 = 9999
# Port number for pgpool
# (change requires restart)
hostname2 = '192.168.40.67'
wd_port2 = 9000
pgpool_port2 = 9999
hostname3 = '192.168.40.64'
wd_port3 = 9000
pgpool_port3 = 9999
need to set: enable_consensus_with_half_votes = on
as 4 nodes with 1 always dead
it works okay and as expected.
Is there an RPM Testing version I could try of the commit from 4 days ago?
Joe Madden
Senior Systems Engineer
D 01412224666
joe.madden at mottmac.com
-----Original Message-----
From: Tatsuo Ishii <ishii at sraoss.co.jp>
Sent: 18 December 2020 13:19
To: Joe Madden <Joe.Madden at mottmac.com>
Cc: pgpool-general at pgpool.net
Subject: Re: [pgpool-general: 7372] Re: Watchdog New Primary & Standby shutdown when Node 0 Fails
> Does anyone know if this commit would cause the issue:
>
> https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fpgpool%2Fpgpool2%2Fcommit%2F70e0b2b93715094823102c9b1879e83fa75c7913&data=04%7C01%7CJoe.Madden%40mottmac.com%7C9f4d36ccbdb54a49a5f708d8a3577bae%7Ca2bed0c459574f73b0c2a811407590fb%7C0%7C0%7C637438943434767785%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=cUHVth1MTeFCeJcvdSaGeQyrqEs%2FHNKsv2BflU%2B5F1A%3D&reserved=0
Asuming you are using 4.2.0 from the log file, this commit surely does
not affect your issue because it was committed after 4.2.0 was out.
Best regards,
--
Tatsuo Ishii
SRA OSS, Inc. Japan
English: https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sraoss.co.jp%2Findex_en.php&data=04%7C01%7CJoe.Madden%40mottmac.com%7C9f4d36ccbdb54a49a5f708d8a3577bae%7Ca2bed0c459574f73b0c2a811407590fb%7C0%7C0%7C637438943434767785%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=fbbKXiccBv8wMdeA9wZ0MxWaYsTJu3TcNaPJGfGpE4U%3D&reserved=0
Japanese:https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.sraoss.co.jp%2F&data=04%7C01%7CJoe.Madden%40mottmac.com%7C9f4d36ccbdb54a49a5f708d8a3577bae%7Ca2bed0c459574f73b0c2a811407590fb%7C0%7C0%7C637438943434767785%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=6iqv00RyeLKQDW3FHAg3dsRXdOW75S23oT7uAnb0ufM%3D&reserved=0
> Joe Madden
> Senior Systems Engineer
> D 01412224666
> joe.madden at mottmac.com<mailto:joe.madden at mottmac.com>
>
> From: Joe Madden
> Sent: 18 December 2020 09:45
> To: pgpool-general at pgpool.net
> Subject: RE: Watchdog New Primary & Standby shutdown when Node 0 Fails
>
> Hi All,
>
> I moved node 0 and Node 2 around (switch the node ids and updated the pgpool config) and I found the same issue on Node 2 (Now 0)
>
> It's got something to do with the Node id and the relevant configs, still don't know if it's a bug for not.
>
> Joe.
>
> Joe Madden
> Senior Systems Engineer
> D 01412224666
> joe.madden at mottmac.com<mailto:joe.madden at mottmac.com>
>
> From: Joe Madden
> Sent: 17 December 2020 18:57
> To: pgpool-general at pgpool.net
> Subject: Watchdog New Primary & Standby shutdown when Node 0 Fails
>
> Hi List,
>
> I've got a PGpool instance with three nodes:
>
> |Pg Pool Node 0 (192.168.40.66)| Pg Pool Node 1 (192.168.40.67)| Pg Pool Node 2 (192.168.40.64)|
>
> Communicate switch back end-
> |Postgresql12 Primary | Postgresql 12 Secondary|
>
>
> This works fine, Standby Nodes 1 & 2 can be shutdown, restarted etc without an issue. When node 0 is shutdown, one of the child processes fails and causes the Nodes 1 and Node 2 to shutdown after about 60 seconds post failover.
>
> I feel like this could be a bug, Our configurations on all three nodes are identical bar the weght pram which is different and node id of course.
>
> Config:
>
> # ----------------------------
> # pgPool-II configuration file
> # ----------------------------
> #
> # This file consists of lines of the form:
> #
> # name = value
> #
> # Whitespace may be used. Comments are introduced with "#" anywhere on a line.
> # The complete list of parameter names and allowed values can be found in the
> # pgPool-II documentation.
> #
> # This file is read on server startup and when the server receives a SIGHUP
> # signal. If you edit the file on a running system, you have to SIGHUP the
> # server for the changes to take effect, or use "pgpool reload". Some
> # parameters, which are marked below, require a server shutdown and restart to
> # take effect.
> #
>
> #------------------------------------------------------------------------------
> # BACKEND CLUSTERING MODE
> # Choose one of: 'streaming_replication', 'native_replication',
> # 'logical_replication', 'slony', 'raw' or 'snapshot_isolation'
> # (change requires restart)
> #------------------------------------------------------------------------------
>
> backend_clustering_mode = 'streaming_replication'
>
> #------------------------------------------------------------------------------
> # CONNECTIONS
> #------------------------------------------------------------------------------
>
> # - pgpool Connection Settings -
>
> listen_addresses = '*'
> # Host name or IP address to listen on:
> # '*' for all, '' for no TCP/IP connections
> # (change requires restart)
> port = 9999
> # Port number
> # (change requires restart)
> socket_dir = '/tmp'
> # Unix domain socket path
> # The Debian package defaults to
> # /var/run/postgresql
> # (change requires restart)
> reserved_connections = 0
> # Number of reserved connections.
> # Pgpool-II does not accept connections if over
> # num_init_chidlren - reserved_connections.
>
>
> # - pgpool Communication Manager Connection Settings -
>
> pcp_listen_addresses = '*'
> # Host name or IP address for pcp process to listen on:
> # '*' for all, '' for no TCP/IP connections
> # (change requires restart)
> pcp_port = 9898
> # Port number for pcp
> # (change requires restart)
> pcp_socket_dir = '/tmp'
> # Unix domain socket path for pcp
> # The Debian package defaults to
> # /var/run/postgresql
> # (change requires restart)
> listen_backlog_multiplier = 2
> # Set the backlog parameter of listen(2) to
> # num_init_children * listen_backlog_multiplier.
> # (change requires restart)
> serialize_accept = off
> # whether to serialize accept() call to avoid thundering herd problem
> # (change requires restart)
>
> # - Backend Connection Settings -
>
> backend_hostname0 = '192.168.40.61'
> # Host name or IP address to connect to for backend 0
> backend_port0 = 5432
> # Port number for backend 0
> backend_weight0 = 1
> # Weight for backend 0 (only in load balancing mode)
> backend_data_directory0 = '/var/lib/pgsql/12/data/'
> # Data directory for backend 0
> backend_flag0 = 'ALLOW_TO_FAILOVER'
> # Controls various backend behavior
> # ALLOW_TO_FAILOVER, DISALLOW_TO_FAILOVER
> # or ALWAYS_PRIMARY
> backend_application_name0 = '192.168.40.61'
> # walsender's application_name, used for "show pool_nodes" command
>
> # - Backend Connection Settings -
>
> backend_hostname1 = '192.168.40.60'
> # Host name or IP address to connect to for backend 0
> backend_port1 = 5432
> # Port number for backend 0
> backend_weight1 = 1
> # Weight for backend 0 (only in load balancing mode)
> backend_data_directory1 = '/var/lib/pgsql/12/data/'
> # Data directory for backend 0
> backend_flag1 = 'ALLOW_TO_FAILOVER'
> # Controls various backend behavior
> # ALLOW_TO_FAILOVER, DISALLOW_TO_FAILOVER
> # or ALWAYS_PRIMARY
> backend_application_name1 = '192.168.40.60'
> # walsender's application_name, used for "show pool_nodes" command
>
>
> # - Authentication -
>
> enable_pool_hba = on
> # Use pool_hba.conf for client authentication
> pool_passwd = 'pool_passwd'
> # File name of pool_passwd for md5 authentication.
> # "" disables pool_passwd.
> # (change requires restart)
> authentication_timeout = 1min
> # Delay in seconds to complete client authentication
> # 0 means no timeout.
>
> allow_clear_text_frontend_auth = off
> # Allow Pgpool-II to use clear text password authentication
> # with clients, when pool_passwd does not
> # contain the user password
>
> # - SSL Connections -
>
> ssl = off
> # Enable SSL support
> # (change requires restart)
> #ssl_key = 'server.key'
> # SSL private key file
> # (change requires restart)
> #ssl_cert = 'server.crt'
> # SSL public certificate file
> # (change requires restart)
> #ssl_ca_cert = ''
> # Single PEM format file containing
> # CA root certificate(s)
> # (change requires restart)
> #ssl_ca_cert_dir = ''
> # Directory containing CA root certificate(s)
> # (change requires restart)
> #ssl_crl_file = ''
> # SSL certificate revocation list file
> # (change requires restart)
>
> ssl_ciphers = 'HIGH:MEDIUM:+3DES:!aNULL'
> # Allowed SSL ciphers
> # (change requires restart)
> ssl_prefer_server_ciphers = off
> # Use server's SSL cipher preferences,
> # rather than the client's
> # (change requires restart)
> ssl_ecdh_curve = 'prime256v1'
> # Name of the curve to use in ECDH key exchange
> ssl_dh_params_file = ''
> # Name of the file containing Diffie-Hellman parameters used
> # for so-called ephemeral DH family of SSL cipher.
> #ssl_passphrase_command=''
> # Sets an external command to be invoked when a passphrase
> # for decrypting an SSL file needs to be obtained
> # (change requires restart)
>
> #------------------------------------------------------------------------------
> # POOLS
> #------------------------------------------------------------------------------
>
> # - Concurrent session and pool size -
>
> num_init_children = 32
> # Number of concurrent sessions allowed
> # (change requires restart)
> max_pool = 4
> # Number of connection pool caches per connection
> # (change requires restart)
>
> # - Life time -
>
> child_life_time = 5min
> # Pool exits after being idle for this many seconds
> child_max_connections = 0
> # Pool exits after receiving that many connections
> # 0 means no exit
> connection_life_time = 0
> # Connection to backend closes after being idle for this many seconds
> # 0 means no close
> client_idle_limit = 0
> # Client is disconnected after being idle for that many seconds
> # (even inside an explicit transactions!)
> # 0 means no disconnection
>
>
> #------------------------------------------------------------------------------
> # LOGS
> #------------------------------------------------------------------------------
>
> # - Where to log -
>
> log_destination = 'stderr'
> # Where to log
> # Valid values are combinations of stderr,
> # and syslog. Default to stderr.
>
> # - What to log -
>
> log_line_prefix = '%t: pid %p: ' # printf-style string to output at beginning of each log line.
>
> log_connections = off
> # Log connections
> log_disconnections = off
> # Log disconnections
> log_hostname = off
> # Hostname will be shown in ps status
> # and in logs if connections are logged
> log_statement = off
> # Log all statements
> log_per_node_statement = off
> # Log all statements
> # with node and backend informations
> log_client_messages = off
> # Log any client messages
> log_standby_delay = 'if_over_threshold'
> # Log standby delay
> # Valid values are combinations of always,
> # if_over_threshold, none
>
> # - Syslog specific -
>
> syslog_facility = 'LOCAL0'
> # Syslog local facility. Default to LOCAL0
> syslog_ident = 'pgpool'
> # Syslog program identification string
> # Default to 'pgpool'
>
> # - Debug -
>
> #log_error_verbosity = default # terse, default, or verbose messages
>
> #client_min_messages = notice # values in order of decreasing detail:
> # debug5
> # debug4
> # debug3
> # debug2
> # debug1
> # log
> # notice
> # warning
> # error
>
> log_min_messages = debug5 # values in order of decreasing detail:
> # debug5
> # debug4
> # debug3
> # debug2
> # debug1
> # info
> # notice
> # warning
> # error
> # log
> # fatal
> # panic
>
> # This is used when logging to stderr:
> #logging_collector = off # Enable capturing of stderr
> # into log files.
> # (change requires restart)
>
> # -- Only used if logging_collector is on ---
>
> #log_directory = '/tmp/pgpool_log' # directory where log files are written,
> # can be absolute
> #log_filename = 'pgpool-%Y-%m-%d_%H%M%S.log'
> # log file name pattern,
> # can include strftime() escapes
>
> #log_file_mode = 0600 # creation mode for log files,
> # begin with 0 to use octal notation
>
> #log_truncate_on_rotation = off # If on, an existing log file with the
> # same name as the new log file will be
> # truncated rather than appended to.
> # But such truncation only occurs on
> # time-driven rotation, not on restarts
> # or size-driven rotation. Default is
> # off, meaning append to existing files
> # in all cases.
>
> #log_rotation_age = 1d # Automatic rotation of logfiles will
> # happen after that (minutes)time.
> # 0 disables time based rotation.
> #log_rotation_size = 10MB # Automatic rotation of logfiles will
> # happen after that much (KB) log output.
> # 0 disables size based rotation.
> #------------------------------------------------------------------------------
> # FILE LOCATIONS
> #------------------------------------------------------------------------------
>
> pid_file_name = '/var/run/pgpool/pgpool.pid'
> # PID file name
> # Can be specified as relative to the"
> # location of pgpool.conf file or
> # as an absolute path
> # (change requires restart)
> logdir = '/tmp'
> # Directory of pgPool status file
> # (change requires restart)
>
>
> #------------------------------------------------------------------------------
> # CONNECTION POOLING
> #------------------------------------------------------------------------------
>
> connection_cache = on
> # Activate connection pools
> # (change requires restart)
>
> # Semicolon separated list of queries
> # to be issued at the end of a session
> # The default is for 8.3 and later
> reset_query_list = 'ABORT; DISCARD ALL'
> # The following one is for 8.2 and before
> #reset_query_list = 'ABORT; RESET ALL; SET SESSION AUTHORIZATION DEFAULT'
>
>
> #------------------------------------------------------------------------------
> # REPLICATION MODE
> #------------------------------------------------------------------------------
>
> replicate_select = off
> # Replicate SELECT statements
> # when in replication mode
> # replicate_select is higher priority than
> # load_balance_mode.
>
> insert_lock = off
> # Automatically locks a dummy row or a table
> # with INSERT statements to keep SERIAL data
> # consistency
> # Without SERIAL, no lock will be issued
> lobj_lock_table = ''
> # When rewriting lo_creat command in
> # replication mode, specify table name to
> # lock
>
> # - Degenerate handling -
>
> replication_stop_on_mismatch = off
> # On disagreement with the packet kind
> # sent from backend, degenerate the node
> # which is most likely "minority"
> # If off, just force to exit this session
>
> failover_if_affected_tuples_mismatch = off
> # On disagreement with the number of affected
> # tuples in UPDATE/DELETE queries, then
> # degenerate the node which is most likely
> # "minority".
> # If off, just abort the transaction to
> # keep the consistency
>
>
> #------------------------------------------------------------------------------
> # LOAD BALANCING MODE
> #------------------------------------------------------------------------------
>
> load_balance_mode = on
> # Activate load balancing mode
> # (change requires restart)
> ignore_leading_white_space = on
> # Ignore leading white spaces of each query
> read_only_function_list = ''
> # Comma separated list of function names
> # that don't write to database
> # Regexp are accepted
> write_function_list = ''
> # Comma separated list of function names
> # that write to database
> # Regexp are accepted
> # If both read_only_function_list and write_function_list
> # is empty, function's volatile property is checked.
> # If it's volatile, the function is regarded as a
> # writing function.
>
> primary_routing_query_pattern_list = ''
> # Semicolon separated list of query patterns
> # that should be sent to primary node
> # Regexp are accepted
> # valid for streaming replicaton mode only.
>
> database_redirect_preference_list = ''
> # comma separated list of pairs of database and node id.
> # example: postgres:primary,mydb[0-4]:1,mydb[5-9]:2'
> # valid for streaming replicaton mode only.
>
> app_name_redirect_preference_list = ''
> # comma separated list of pairs of app name and node id.
> # example: 'psql:primary,myapp[0-4]:1,myapp[5-9]:standby'
> # valid for streaming replicaton mode only.
> allow_sql_comments = off
> # if on, ignore SQL comments when judging if load balance or
> # query cache is possible.
> # If off, SQL comments effectively prevent the judgment
> # (pre 3.4 behavior).
>
> disable_load_balance_on_write = 'transaction'
> # Load balance behavior when write query is issued
> # in an explicit transaction.
> #
> # Valid values:
> #
> # 'transaction' (default):
> # if a write query is issued, subsequent
> # read queries will not be load balanced
> # until the transaction ends.
> #
> # 'trans_transaction':
> # if a write query is issued, subsequent
> # read queries in an explicit transaction
> # will not be load balanced until the session ends.
> #
> # 'dml_adaptive':
> # Queries on the tables that have already been
> # modified within the current explicit transaction will
> # not be load balanced until the end of the transaction.
> #
> # 'always':
> # if a write query is issued, read queries will
> # not be load balanced until the session ends.
> #
> # Note that any query not in an explicit transaction
> # is not affected by the parameter.
>
> dml_adaptive_object_relationship_list= ''
> # comma separated list of object pairs
> # [object]:[dependent-object], to disable load balancing
> # of dependent objects within the explicit transaction
> # after WRITE statement is issued on (depending-on) object.
> #
> # example: 'tb_t1:tb_t2,insert_tb_f_func():tb_f,tb_v:my_view'
> # Note: function name in this list must also be present in
> # the write_function_list
> # only valid for disable_load_balance_on_write = 'dml_adaptive'.
>
> statement_level_load_balance = off
> # Enables statement level load balancing
>
> #------------------------------------------------------------------------------
> # NATIVE REPLICATION MODE
> #------------------------------------------------------------------------------
>
> # - Streaming -
>
> sr_check_period = 10
> # Streaming replication check period
> # Disabled (0) by default
> sr_check_user = 'repmgr'
> # Streaming replication check user
> # This is neccessary even if you disable streaming
> # replication delay check by sr_check_period = 0
> sr_check_password = '###################'
> # Password for streaming replication check user
> # Leaving it empty will make Pgpool-II to first look for the
> # Password in pool_passwd file before using the empty password
>
> sr_check_database = 'repmgr'
> # Database name for streaming replication check
> delay_threshold = 10000000
> # Threshold before not dispatching query to standby node
> # Unit is in bytes
> # Disabled (0) by default
>
> # - Special commands -
>
> follow_primary_command = ''
> # Executes this command after main node failover
> # Special values:
> # %d = failed node id
> # %h = failed node host name
> # %p = failed node port number
> # %D = failed node database cluster path
> # %m = new main node id
> # %H = new main node hostname
> # %M = old main node id
> # %P = old primary node id
> # %r = new main port number
> # %R = new main database cluster path
> # %N = old primary node hostname
> # %S = old primary node port number
> # %% = '%' character
>
> #------------------------------------------------------------------------------
> # HEALTH CHECK GLOBAL PARAMETERS
> #------------------------------------------------------------------------------
>
> health_check_period = 5
> # Health check period
> # Disabled (0) by default
> health_check_timeout = 20
> # Health check timeout
> # 0 means no timeout
> health_check_user = 'pgpool'
> # Health check user
> health_check_password = '#############################'
> # Password for health check user
> # Leaving it empty will make Pgpool-II to first look for the
> # Password in pool_passwd file before using the empty password
>
> health_check_database = 'postgres'
> # Database name for health check. If '', tries 'postgres' frist,
> health_check_max_retries = 3
> # Maximum number of times to retry a failed health check before giving up.
> health_check_retry_delay = 1
> # Amount of time to wait (in seconds) between retries.
> connect_timeout = 10000
> # Timeout value in milliseconds before giving up to connect to backend.
> # Default is 10000 ms (10 second). Flaky network user may want to increase
> # the value. 0 means no timeout.
> # Note that this value is not only used for health check,
> # but also for ordinary conection to backend.
>
> #------------------------------------------------------------------------------
> # HEALTH CHECK PER NODE PARAMETERS (OPTIONAL)
> #------------------------------------------------------------------------------
> #health_check_period0 = 0
> #health_check_timeout0 = 20
> #health_check_user0 = 'nobody'
> #health_check_password0 = ''
> #health_check_database0 = ''
> #health_check_max_retries0 = 0
> #health_check_retry_delay0 = 1
> #connect_timeout0 = 10000
>
> #------------------------------------------------------------------------------
> # FAILOVER AND FAILBACK
> #------------------------------------------------------------------------------
>
> #failover_command = '/opt/pgpool/scripts/failover.sh %d %h %p %D %m %H %M %P %r %R'
> failover_command = '/etc/pgpool-II/failover.sh %d %H %h %p %D %m %M %P %r %R %N %S'
> # Executes this command at failover
> # Special values:
> # %d = failed node id
> # %h = failed node host name
> # %p = failed node port number
> # %D = failed node database cluster path
> # %m = new main node id
> # %H = new main node hostname
> # %M = old main node id
> # %P = old primary node id
> # %r = new main port number
> # %R = new main database cluster path
> # %N = old primary node hostname
> # %S = old primary node port number
> # %% = '%' character
> failback_command = ''
> # Executes this command at failback.
> # Special values:
> # %d = failed node id
> # %h = failed node host name
> # %p = failed node port number
> # %D = failed node database cluster path
> # %m = new main node id
> # %H = new main node hostname
> # %M = old main node id
> # %P = old primary node id
> # %r = new main port number
> # %R = new main database cluster path
> # %N = old primary node hostname
> # %S = old primary node port number
> # %% = '%' character
>
> failover_on_backend_error = on
> # Initiates failover when reading/writing to the
> # backend communication socket fails
> # If set to off, pgpool will report an
> # error and disconnect the session.
>
> detach_false_primary = on
> # Detach false primary if on. Only
> # valid in streaming replicaton
> # mode and with PostgreSQL 9.6 or
> # after.
>
> search_primary_node_timeout = 5min
> # Timeout in seconds to search for the
> # primary node when a failover occurs.
> # 0 means no timeout, keep searching
> # for a primary node forever.
>
> #------------------------------------------------------------------------------
> # ONLINE RECOVERY
> #------------------------------------------------------------------------------
>
> recovery_user = 'nobody'
> # Online recovery user
> recovery_password = ''
> # Online recovery password
> # Leaving it empty will make Pgpool-II to first look for the
> # Password in pool_passwd file before using the empty password
>
> recovery_1st_stage_command = ''
> # Executes a command in first stage
> recovery_2nd_stage_command = ''
> # Executes a command in second stage
> recovery_timeout = 90
> # Timeout in seconds to wait for the
> # recovering node's postmaster to start up
> # 0 means no wait
> client_idle_limit_in_recovery = 0
> # Client is disconnected after being idle
> # for that many seconds in the second stage
> # of online recovery
> # 0 means no disconnection
> # -1 means immediate disconnection
>
> auto_failback = on
> # Dettached backend node reattach automatically
> # if replication_state is 'streaming'.
> auto_failback_interval = 1min
> # Min interval of executing auto_failback in
> # seconds.
>
> #------------------------------------------------------------------------------
> # WATCHDOG
> #------------------------------------------------------------------------------
>
> # - Enabling -
>
> use_watchdog = on
> # Activates watchdog
> # (change requires restart)
>
> # -Connection to up stream servers -
>
> trusted_servers = ''
> # trusted server list which are used
> # to confirm network connection
> # (hostA,hostB,hostC,...)
> # (change requires restart)
> ping_path = '/bin'
> # ping command path
> # (change requires restart)
>
> # - Watchdog communication Settings -
>
> hostname0 = '192.168.40.66'
> # Host name or IP address of pgpool node
> # for watchdog connection
> # (change requires restart)
> wd_port0 = 9000
> # Port number for watchdog service
> # (change requires restart)
> pgpool_port0 = 9999
> # Port number for pgpool
> # (change requires restart)
>
>
> hostname1 = '192.168.40.67'
> wd_port1 = 9000
> pgpool_port1 = 9999
>
> hostname2 = '192.168.40.64'
> wd_port2 = 9000
> pgpool_port2 = 9999
>
>
> wd_priority = 90
> # priority of this watchdog in leader election
> # (change requires restart)
>
> wd_authkey = '###################################'
> # Authentication key for watchdog communication
> # (change requires restart)
>
> wd_ipc_socket_dir = '/tmp'
> # Unix domain socket path for watchdog IPC socket
> # The Debian package defaults to
> # /var/run/postgresql
> # (change requires restart)
>
>
> # - Virtual IP control Setting -
>
> delegate_IP = '192.168.40.70'
> # delegate IP address
> # If this is empty, virtual IP never bring up.
> # (change requires restart)
> if_cmd_path = '/sbin'
> # path to the directory where if_up/down_cmd exists
> # If if_up/down_cmd starts with "/", if_cmd_path will be ignored.
> # (change requires restart)
> if_up_cmd = '/usr/bin/sudo /sbin/ip addr add $_IP_$/24 dev eth0 label eth0:0'
> # startup delegate IP command
> # (change requires restart)
> if_down_cmd = '/usr/bin/sudo /sbin/ip addr del $_IP_$/24 dev eth0'
> # shutdown delegate IP command
> # (change requires restart)
> arping_path = '/usr/sbin'
> # arping command path
> # If arping_cmd starts with "/", if_cmd_path will be ignored.
> # (change requires restart)
> arping_cmd = '/usr/bin/sudo /usr/sbin/arping -U $_IP_$ -w 1 -I eth0'
> # arping command
> # (change requires restart)
>
> # - Behaivor on escalation Setting -
>
> clear_memqcache_on_escalation = on
> # Clear all the query cache on shared memory
> # when standby pgpool escalate to active pgpool
> # (= virtual IP holder).
> # This should be off if client connects to pgpool
> # not using virtual IP.
> # (change requires restart)
> wd_escalation_command = ''
> # Executes this command at escalation on new active pgpool.
> # (change requires restart)
> wd_de_escalation_command = ''
> # Executes this command when leader pgpool resigns from being leader.
> # (change requires restart)
>
> # - Watchdog consensus settings for failover -
>
> failover_when_quorum_exists = on
> # Only perform backend node failover
> # when the watchdog cluster holds the quorum
> # (change requires restart)
>
> failover_require_consensus = on
> # Perform failover when majority of Pgpool-II nodes
> # aggrees on the backend node status change
> # (change requires restart)
>
> allow_multiple_failover_requests_from_node = off
> # A Pgpool-II node can cast multiple votes
> # for building the consensus on failover
> # (change requires restart)
>
>
> enable_consensus_with_half_votes = off
> # apply majority rule for consensus and quorum computation
> # at 50% of votes in a cluster with even number of nodes.
> # when enabled the existence of quorum and consensus
> # on failover is resolved after receiving half of the
> # total votes in the cluster, otherwise both these
> # decisions require at least one more vote than
> # half of the total votes.
> # (change requires restart)
>
> # - Lifecheck Setting -
>
> # -- common --
>
> wd_monitoring_interfaces_list = 'any' # Comma separated list of interfaces names to monitor.
> # if any interface from the list is active the watchdog will
> # consider the network is fine
> # 'any' to enable monitoring on all interfaces except loopback
> # '' to disable monitoring
> # (change requires restart)
>
> wd_lifecheck_method = 'heartbeat'
> # Method of watchdog lifecheck ('heartbeat' or 'query' or 'external')
> # (change requires restart)
> wd_interval = 10
> # lifecheck interval (sec) > 0
> # (change requires restart)
>
> # -- heartbeat mode --
>
> heartbeat_hostname0 = '192.168.40.66'
> # Host name or IP address used
> # for sending heartbeat signal.
> # (change requires restart)
> heartbeat_port0 = 9694
> # Port number used for receiving/sending heartbeat signal
> # Usually this is the same as heartbeat_portX.
> # (change requires restart)
> heartbeat_device0 = 'eth0'
> # Name of NIC device (such like 'eth0')
> # used for sending/receiving heartbeat
> # signal to/from destination 0.
> # This works only when this is not empty
> # and pgpool has root privilege.
> # (change requires restart)
>
> heartbeat_hostname1 = '192.168.40.67'
> heartbeat_port1 = 9694
> heartbeat_device1 = 'eth0'
>
> heartbeat_hostname2 = '192.168.40.64'
> heartbeat_port2 = 9694
> heartbeat_device2 = 'eth0'
>
> wd_heartbeat_keepalive = 2
> # Interval time of sending heartbeat signal (sec)
> # (change requires restart)
> wd_heartbeat_deadtime = 30
> # Deadtime interval for heartbeat signal (sec)
> # (change requires restart)
>
> # -- query mode --
>
> wd_life_point = 3
> # lifecheck retry times
> # (change requires restart)
> wd_lifecheck_query = 'SELECT 1'
> # lifecheck query to pgpool from watchdog
> # (change requires restart)
> wd_lifecheck_dbname = 'template1'
> # Database name connected for lifecheck
> # (change requires restart)
> wd_lifecheck_user = 'nobody'
> # watchdog user monitoring pgpools in lifecheck
> # (change requires restart)
> wd_lifecheck_password = ''
> # Password for watchdog user in lifecheck
> # Leaving it empty will make Pgpool-II to first look for the
> # Password in pool_passwd file before using the empty password
> # (change requires restart)
>
> #------------------------------------------------------------------------------
> # OTHERS
> #------------------------------------------------------------------------------
> relcache_expire = 0
> # Life time of relation cache in seconds.
> # 0 means no cache expiration(the default).
> # The relation cache is used for cache the
> # query result against PostgreSQL system
> # catalog to obtain various information
> # including table structures or if it's a
> # temporary table or not. The cache is
> # maintained in a pgpool child local memory
> # and being kept as long as it survives.
> # If someone modify the table by using
> # ALTER TABLE or some such, the relcache is
> # not consistent anymore.
> # For this purpose, cache_expiration
> # controls the life time of the cache.
> relcache_size = 256
> # Number of relation cache
> # entry. If you see frequently:
> # "pool_search_relcache: cache replacement happend"
> # in the pgpool log, you might want to increate this number.
>
> check_temp_table = catalog
> # Temporary table check method. catalog, trace or none.
> # Default is catalog.
>
> check_unlogged_table = on
> # If on, enable unlogged table check in SELECT statements.
> # This initiates queries against system catalog of primary/main
> # thus increases load of primary.
> # If you are absolutely sure that your system never uses unlogged tables
> # and you want to save access to primary/main, you could turn this off.
> # Default is on.
> enable_shared_relcache = on
> # If on, relation cache stored in memory cache,
> # the cache is shared among child process.
> # Default is on.
> # (change requires restart)
>
> relcache_query_target = primary # Target node to send relcache queries. Default is primary node.
> # If load_balance_node is specified, queries will be sent to load balance node.
> #------------------------------------------------------------------------------
> # IN MEMORY QUERY MEMORY CACHE
> #------------------------------------------------------------------------------
> memory_cache_enabled = off
> # If on, use the memory cache functionality, off by default
> # (change requires restart)
> memqcache_method = 'shmem'
> # Cache storage method. either 'shmem'(shared memory) or
> # 'memcached'. 'shmem' by default
> # (change requires restart)
> memqcache_memcached_host = 'localhost'
> # Memcached host name or IP address. Mandatory if
> # memqcache_method = 'memcached'.
> # Defaults to localhost.
> # (change requires restart)
> memqcache_memcached_port = 11211
> # Memcached port number. Mondatory if memqcache_method = 'memcached'.
> # Defaults to 11211.
> # (change requires restart)
> memqcache_total_size = 64MB
> # Total memory size in bytes for storing memory cache.
> # Mandatory if memqcache_method = 'shmem'.
> # Defaults to 64MB.
> # (change requires restart)
> memqcache_max_num_cache = 1000000
> # Total number of cache entries. Mandatory
> # if memqcache_method = 'shmem'.
> # Each cache entry consumes 48 bytes on shared memory.
> # Defaults to 1,000,000(45.8MB).
> # (change requires restart)
> memqcache_expire = 0
> # Memory cache entry life time specified in seconds.
> # 0 means infinite life time. 0 by default.
> # (change requires restart)
> memqcache_auto_cache_invalidation = on
> # If on, invalidation of query cache is triggered by corresponding
> # DDL/DML/DCL(and memqcache_expire). If off, it is only triggered
> # by memqcache_expire. on by default.
> # (change requires restart)
> memqcache_maxcache = 400kB
> # Maximum SELECT result size in bytes.
> # Must be smaller than memqcache_cache_block_size. Defaults to 400KB.
> # (change requires restart)
> memqcache_cache_block_size = 1MB
> # Cache block size in bytes. Mandatory if memqcache_method = 'shmem'.
> # Defaults to 1MB.
> # (change requires restart)
> memqcache_oiddir = '/var/log/pgpool/oiddir'
> # Temporary work directory to record table oids
> # (change requires restart)
> cache_safe_memqcache_table_list = ''
> # Comma separated list of table names to memcache
> # that don't write to database
> # Regexp are accepted
> cache_unsafe_memqcache_table_list = ''
> # Comma separated list of table names not to memcache
> # that don't write to database
> # Regexp are accepted
>
> Error output:
>
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: setting the local watchdog node name to "192.168.40.67:9999 Linux SVD-SLB02"
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: watchdog cluster is configured with 2 remote nodes
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: watchdog remote node:0 on 192.168.40.66:9000
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: watchdog remote node:1 on 192.168.40.64:9000
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: ensure availibility on any interface
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: watchdog node state changed from [DEAD] to [LOADING]
> Dec 17 18:39:49 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:49: pid 1332675: LOG: new outbound connection to 192.168.40.64:9000
> Dec 17 18:39:50 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:50: pid 1332675: LOG: new watchdog node connection is received from "192.168.40.66:62151"
> Dec 17 18:39:50 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:50: pid 1332675: LOG: new node joined the cluster hostname:"192.168.40.66" port:9000 pgpool_port:9999
> Dec 17 18:39:50 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:50: pid 1332675: DETAIL: Pgpool-II version:"4.2.0" watchdog messaging version: 1.2
> Dec 17 18:39:53 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:53: pid 1332675: LOG: watchdog node state changed from [LOADING] to [INITIALIZING]
> Dec 17 18:39:54 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:54: pid 1332675: LOG: watchdog node state changed from [INITIALIZING] to [STANDING FOR LEADER]
> Dec 17 18:39:54 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:54: pid 1332675: LOG: watchdog node state changed from [STANDING FOR LEADER] to [PARTICIPATING IN ELECTION]
> Dec 17 18:39:54 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:54: pid 1332675: LOG: watchdog node state changed from [PARTICIPATING IN ELECTION] to [INITIALIZING]
> Dec 17 18:39:54 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:54: pid 1332675: LOG: setting the remote node "192.168.40.66:9999 Linux SVD-SLB01" as watchdog cluster leader
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: watchdog node state changed from [INITIALIZING] to [STANDBY]
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: successfully joined the watchdog cluster as standby node
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: DETAIL: our join coordinator request is accepted by cluster leader node "192.168.40.66:9999 Linux SVD-SLB01"
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: new IPC connection received
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: new IPC connection received
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: new IPC connection received
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: new IPC connection received
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: received the get data request from local pgpool-II on IPC interface
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: LOG: get data request from local pgpool-II node received on IPC interface is forwarded to leader watchdog node "192.168.40.66:9999 Linux SVD-SLB01"
> Dec 17 18:39:55 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:55: pid 1332675: DETAIL: waiting for the reply...
> Dec 17 18:39:59 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:59: pid 1332675: LOG: new watchdog node connection is received from "192.168.40.64:15019"
> Dec 17 18:39:59 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:59: pid 1332675: LOG: new node joined the cluster hostname:"192.168.40.64" port:9000 pgpool_port:9999
> Dec 17 18:39:59 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:39:59: pid 1332675: DETAIL: Pgpool-II version:"4.2.0" watchdog messaging version: 1.2
> Dec 17 18:40:00 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:00: pid 1332675: LOG: new outbound connection to 192.168.40.66:9000
> Dec 17 18:40:44 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:44: pid 1332675: LOG: remote node "192.168.40.66:9999 Linux SVD-SLB01" is shutting down
> Dec 17 18:40:44 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:44: pid 1332675: LOG: watchdog cluster has lost the coordinator node
> Dec 17 18:40:44 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:44: pid 1332675: LOG: removing the remote node "192.168.40.66:9999 Linux SVD-SLB01" from watchdog cluster leader
> Dec 17 18:40:44 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:44: pid 1332675: LOG: We have lost the cluster leader node "192.168.40.66:9999 Linux SVD-SLB01"
> Dec 17 18:40:44 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:44: pid 1332675: LOG: watchdog node state changed from [STANDBY] to [JOINING]
> Dec 17 18:40:44 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:44: pid 1332675: LOG: watchdog node state changed from [JOINING] to [INITIALIZING]
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: watchdog node state changed from [INITIALIZING] to [STANDING FOR LEADER]
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: watchdog node state changed from [STANDING FOR LEADER] to [LEADER]
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: I am announcing my self as leader/coordinator watchdog node
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: I am the cluster leader node
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: DETAIL: our declare coordinator message is accepted by all nodes
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: setting the local node "192.168.40.67:9999 Linux SVD-SLB02" as watchdog cluster leader
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: I am the cluster leader node but we do not have enough nodes in cluster
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: DETAIL: waiting for the quorum to start escalation process
> Dec 17 18:40:45 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:45: pid 1332675: LOG: new IPC connection received
> Dec 17 18:40:46 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:46: pid 1332675: LOG: adding watchdog node "192.168.40.64:9999 Linux SVD-WEB01" to the standby list
> Dec 17 18:40:46 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:46: pid 1332675: LOG: quorum found
> Dec 17 18:40:46 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:46: pid 1332675: DETAIL: starting escalation process
> Dec 17 18:40:46 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:46: pid 1332675: LOG: escalation process started with PID:1332782
> Dec 17 18:40:46 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:46: pid 1332675: LOG: new IPC connection received
> Dec 17 18:40:46 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:46: pid 1332675: LOG: new IPC connection received
> Dec 17 18:40:50 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:40:50: pid 1332675: LOG: watchdog escalation process with pid: 1332782 exit with SUCCESS.
> Dec 17 18:41:03 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:41:03: pid 1332675: LOG: new watchdog node connection is received from "192.168.40.66:55496"
> Dec 17 18:41:03 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:41:03: pid 1332675: LOG: new node joined the cluster hostname:"192.168.40.66" port:9000 pgpool_port:9999
> Dec 17 18:41:03 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:41:03: pid 1332675: DETAIL: Pgpool-II version:"4.2.0" watchdog messaging version: 1.2
> Dec 17 18:41:03 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:41:03: pid 1332675: LOG: The newly joined node:"192.168.40.66:9999 Linux SVD-SLB01" had left the cluster because it was shutdown
> Dec 17 18:41:03 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:41:03: pid 1332675: LOG: new outbound connection to 192.168.40.66:9000
> Dec 17 18:41:04 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:41:04: pid 1332675: LOG: adding watchdog node "192.168.40.66:9999 Linux SVD-SLB01" to the standby list
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: read from socket failed, remote end closed the connection
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: client socket of 192.168.40.66:9999 Linux SVD-SLB01 is closed
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: read from socket failed, remote end closed the connection
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: outbound socket of 192.168.40.66:9999 Linux SVD-SLB01 is closed
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: remote node "192.168.40.66:9999 Linux SVD-SLB01" is not reachable
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: DETAIL: marking the node as lost
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: remote node "192.168.40.66:9999 Linux SVD-SLB01" is lost
> Dec 17 18:42:51 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:42:51: pid 1332675: LOG: removing watchdog node "192.168.40.66:9999 Linux SVD-SLB01" from the standby list
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: new IPC connection received
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: read from socket failed, remote end closed the connection
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: client socket of 192.168.40.64:9999 Linux SVD-WEB01 is closed
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: remote node "192.168.40.64:9999 Linux SVD-WEB01" is shutting down
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: removing watchdog node "192.168.40.64:9999 Linux SVD-WEB01" from the standby list
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: We have lost the quorum
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: received node status change ipc message
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: DETAIL: No heartbeat signal from node
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: WARNING: watchdog life-check reported, we are disconnected from the network
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: DETAIL: changing the state to LOST
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: watchdog node state changed from [LEADER] to [LOST]
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: FATAL: system has lost the network
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332675: LOG: Watchdog is shutting down
> Dec 17 18:43:25 SVD-SLB02 pgpool[1332673]: 2020-12-17 18:43:25: pid 1332673: LOG: watchdog child process with pid: 1332675 exits with status 768
>
> Does anyone have any suggestions of what this could be?
>
> Note if I play around with the weights I can get the other node to be the VIP but it still shutdowns with node 0 is shutdown.
>
> It does not shutdown when any of the other nodes are shutdown, only node 0
>
> Thanks,
>
> Joe
>
More information about the pgpool-general
mailing list